Balancing is a must anytime tires are mounted on wheels, and many would argue that it is also a good idea to rebalance a tire and wheel assembly if a tire has been dismounted for repair.
Balancing provides a smoother ride by minimizing tire bounce. This helps improve traction, steering control and extends the life of the tires. But no matter how carefully the tires are balanced, they will eventually lose their balance. As the tread wears, the distribution of weight around the circumference of a tire changes, altering the balance of the tire and wheel assembly. Eventually the tire may have to be rebalanced because only 1/4 ounce of imbalance can produce a noticeable vibration.
Symptoms of Tire Imbalance
An out-of-balance tire and wheel will typically create a vibration or shake that becomes progressively worse as the vehicle speed increases. The speed at which the vibration first becomes apparent will vary depending on the size and weight of the tires and wheels, the size and weight of the vehicle, the sensitivity of the steering and suspension and the amount of imbalance, but usually starts at 40 to 50 mph and increases in intensity as the speed goes up.
Tire/Wheel Balance Diagnosis
If you have a tire/wheel vibration problem, take your vehicle to a tire store or repair facility that has a tire balancinhg machine. Have them check the balance of all four wheels and tires, and have any wheels that are out-of-balance rebalance as needed.
It is also important to remember that speed-sensitive vibrations can also be caused by radial (vertical) or lateral (sideways) runout in a tire, wheel or hub. Loose, worn or damaged wheel bearings as well as certain kinds of tread wear can also cause vibrations. So too can an out-of-balance or out-of-phase rear-wheel-drive driveshaft (FWD shafts usually do not rotate fast enough to cause vibration problems.)
When troubleshooting the cause of a speed-sensitive vibration, start by inspecting the tires and wheels. Look for evidence of missing weights, mud or dirt packed in the back of the rim or debris embedded in the tread that could create an imbalance.
Note the amount of wear on the tread. If the tires are more than 50 percent worn, chances are they have not been rebalanced since they were new. Be sure to measure tread depth at several points around the circumference of the tire. This will tell you if the tread is wearing evenly and if the depth is equal. A difference of more than about 1/16 inch would indicate an out-of-round condition.
Tire/Wheel Runout Can Cause Vibrations
Most tires should probably have less than .050 inch of radial runout, and some even less depending on how sensitive the vehicle’s steering and suspension (and driver) are to vibration. Runout problems can often be corrected by “match-mounting” the tire on the wheel (rotating the tire so the tire high spot is over the rim low spot). Also, rotate and wiggle each wheel by hand to check for excessive play or noise from the wheel bearings.
Tires can sometimes go out of balance almost immediately if the tire slips (turns) on its rim. This can happen if someone uses a lubricant such as silicone on the tire bead or rim when mounting tires on aluminum alloy wheels. Hard braking or acceleration can cause the tire to rotate on the rim, destroying the original balance.
Wheel Balancing Equipment
To accurately balance tires and wheels, an electronic spin balancer that can achieve both static (at rest) and dynamic (in motion) balance should be used. Old fashioned bubble balancers can do a decent job of achieving static balance, but dynamic balance can only be achieved with a spin balancer. This is especially important with today’s larger, wider, heavier tire and rim packages and absolutely essential for run-flat tires that have thicker, stiffer sidewalls.
Some balancing equipment is capable of detecting runout problems in the tire and wheel assembly as well as vibrations in sidewall stiffness that may cause vibrations. One such balancer applies a roller against the tire to simulate a load on the tire as it rotates. If the unit detects a stiff spot in the sidewall, it tells the operator how to reposition the tire on the wheel so the stiffest part of the tire will be over the lowest point on the rim.
Most balancers today have self-calibrating electronics with accuracy to hundredths of an ounce (or tenths of a gram). Graphical displays also make information easier to read and understand, and reduce the chance of making a mistake. Automatic data entry for wheel width and diameter on some balancers also saves time.
Most balancers today operate at lower speeds. This helps extend motor life and reduces cycle times as well as risk to the operator. Older balancers typically had to spin a wheel fairly fast (about 500 rpm, or the equivalent of 55 to 60 mph) to generate a usable signal. But the more sensitive electronics in newer balancers are able to pick up vibrations at much lower speeds (only 100 rpm, or 10 to 15 mph).
So, the next time you encounter a speed-related vibration, you may have an out-of-balance tire/wheel assembly, or too much runout in the tire or wheel.
|WARNING: DO NOT USE OIL, GREASE, ANTI-SEIZE OR LUBRICANTS OF ANY KIND WHEN TIGHTENING LUG NUTS!|
Proper torque on lug nuts is very important for three reasons. One is to keep the lug nuts from loosening up and the wheel coming loose, another is to prevent distortion of the brake rotor behind the wheel, and a third is to prevent broken studs. A torque wrench should be used for final tightening of the lug nuts, and the nuts should always be torqued to the recommended specifications.
CAUTION: Torque specifications for lug nuts are always for CLEANand DRY studs and lug nuts. That means no oil, no grease, no anti-seize and no lubricants of any kind. Any of these products will reduce the friction between the threads. This may seem like a good thing to prevent rust and frozen lug nuts, but the reduction in friction means a much higher percentage of the applied torque (up to 25% or more) will go toward loading the lug nuts. The end result may be brake rotor distortion or broken studs!
Wheel studs should be cleaned with a wire brush to remove rust and dirt BEFORE the wheels are mounted. If the lug nuts are heavily rusted or have damaged threads and won’t turn easily on the studs, replace the lug nuts. The same goes for any wheel studs with damaged or badly corroded threads. And remember to mount the wheels DRY with nothing on the threads.